01-03 Dimensions and Deck Type
 |
 |
|
| Gross vehicle weight rating (GVWR) | ||
|---|---|---|
| 65,000 lb | ||
| Payload capacity | ||
| 55,000 lb | ||
| Inside height | ||
| 104⅛" | ||
| Inside width | ||
| 97½" at wearband | ||
| Overall length | ||
| 53' 0" | ||
| Overall height | ||
| 13' 6" on 46½" height 5th wheel | ||
| Overall width | ||
| 102⅜" | ||
|
|
|
| Deck type | ||
| Straight | ||
04 Front Subframe
|
|
|
| Front subframe | ||
|---|---|---|
| 4¼" deep box beam design | ||
| Approach plate | ||
| 9 ga. high strength steel full width | ||
| Kingpin location | ||
| 36" from front | ||
| Kingpin plate | ||
| 3 ga. high strength steel full width | ||
| Kingpin type | ||
| AAR hardness cruciform | ||
| Cover plate | ||
| Extruded aluminum on front face of approach plate | ||
05 Support Leg and Assembly
|
|
|
| Support legs | ||
|---|---|---|
| Jost® model A401 enhanced 50,000 lb capacity | ||
| Support leg location | ||
| 105" from center line of kingpin to center line of support legs | ||
| Support leg shoe type | ||
| 10" × 10" ultra low profile cushion foot | ||
| Support leg bracing | ||
| Bolt-on cross-bracing with 7 ga. 3¼" deep high strength steel channels | ||
| Support leg crank location | ||
| Roadside of support legs | ||
06 Crossmembers and Rails
|
|
|
| Bottom rails | ||
|---|---|---|
| 11" deep heavy-duty extruded aluminum; tapered front and rear | ||
| Crossmembers front subframe to legs | ||
| 4" aluminum I-beam crossmembers with 4 rivet end clips on 12" center line | ||
| Crossmembers legs to rear subframe | ||
| 5½" aluminum I-beam crossmembers with 4 rivet end clips on 12" center line | ||
| Crossmembers over rear subframe | ||
| 4" steel I-beam crossmembers with 4 rivet end clips on 12" center line with standard reinforcement of an additional crossmember in rear 34" | ||
| Crossmembers over support legs | ||
| (5) 4" steel I-beam crossmembers with 4 rivet end clips on 12" center line over legs | ||
07 Rear Subframe
|
|
|
| Rubber dock bumpers | ||
|---|---|---|
| 1 pair | ||
| Vertical and horizontal I.C.C. bumper | ||
| D.O.T. high strength steel vertical with non-slip 7" deep horizontal | ||
08 Suspension, Axles and Actuation
|
|
|
| Hendrickson air ride system with integral axles | ||
|---|---|---|
| Hendrickson® ULTRAA-K air ride/slider system with 49" axle spacing | ||
| Slider suspension location | ||
| 70" rear and 166" forward for 96" of slider travel | ||
| Slack adjusters | ||
| Bendix® Versajust® automatic | ||
| Slider pin release mechanism | ||
| Hendrickson® Quik-Draw® air-operated slider repositioning system | ||
| Air actuation system | ||
| 1 tank with spring brakes | ||
| Air brake chambers | ||
| Bendix® EnduraSure™ 3030 | ||
| Air ride dump valve | ||
| Hendrickson® automatic | ||
|
|
|
| Anti-lock brake system (ABS) | ||
| Bendix® TABS-8 2S/1M with trailer roll stability | ||
| Axle spindle nuts | ||
| ConMet® included with Preset Plus® | ||
| Brake lining style | ||
| Hendrickson® HXS brake lining style | ||
| Hub piloted system with outboard drums | ||
| 10 stud hub-piloted system with outboard balanced SJD-XL3 steel jacketed lightweight drums with 16-1/2" × 7" brakes (standard with ConMet Preset Plus®) | ||
| Hubcaps | ||
| ConMet® included with Preset Plus® | ||
| Oil seals | ||
| ConMet® included with Preset Plus® | ||
| Wheel bearing lubrication | ||
| Mobilube HD Plus 80W-90 oil | ||
|
|
|
| Wheel bearings | ||
| ConMet® included with Preset Plus® | ||
09 Front Wall
|
|
|
| Front panels | ||
|---|---|---|
| .040" aluminum, pre-painted white with Ultra Road Shield™ Plus (URS+) | ||
| Front wall posts | ||
| 1" J-shaped extruded aluminum post with 2 additional 3¼' deep steel reefer unit support posts | ||
| Front corner post | ||
| .080" extruded aluminum 4¾" radius | ||
| Front top rail | ||
| Extruded aluminum wraparound | ||
| Gladhands and receptacle location | ||
| Gladhands and receptacle mounted on an aluminum extrusion offset to roadside | ||
| Prep for front mount refrigeration unit | ||
| Without electric standby | ||
| Refrigeration unit opening cover | ||
| Sheet metal cover includes sealant full perimeter of opening | ||
|
|
|
10 Side Wall
|
|
|
| Side panels | ||
|---|---|---|
| .040" aluminum flat side panels, pre-painted white with Ultra Road Shield™ Plus (URS+) | ||
| Side posts | ||
| 1" J-shape extruded aluminum posts with 16" maximum center line from front to rear of support legs with 24" center line legs to rear; 2 additional posts each side over front subframe | ||
11 Roof
|
|
|
| Roof skin | ||
|---|---|---|
| .025" one-piece aluminum coil | ||
| Roof bows | ||
| 1" extruded aluminum J-shaped bows on 48" center lines | ||
| Top rails | ||
| 6⅜" heavy-duty extruded aluminum | ||
12 Rear Case and Doors
|
|
|
| Rear case & buckplate material | ||
|---|---|---|
| Stainless steel for satin finish swing doors | ||
| Rear case corner posts & header | ||
| Stainless steel for satin finish swing doors | ||
| Rear door hinge material | ||
| Non-polished aluminum | ||
| Rear door hinges | ||
| 4 per door | ||
| Holdbacks | ||
| Chain link and hook type door | ||
| Rear door lock rods | ||
| 1 per door | ||
| Rear door panels | ||
| .040" aluminum exterior panel | ||
|
|
|
| Rear door type | ||
| Utility-Design Barrier Door® | ||
14 Floors
|
|
|
| Floor type | ||
|---|---|---|
| 1½" extruded aluminum high wear 20K duct floor system and integral 10" heavy-duty extruded aluminum non-tapered wearband | ||
| Fork lift reinforcing | ||
| Bearing grid system at rear with full width hardwood fillers and aluminum I-cores rear 36" of floor in center 68"; 1 additional crossmember at rear for maximum 6" center line at rear 34" | ||
| Troughs | ||
| Extruded aluminum front and rear | ||
| Drains | ||
| 2 drains front and rear | ||
15 Insulation
|
|
|
| Insulation type | ||
|---|---|---|
| Polyurethane insulation Foam-In-Place using low-GWP Solstice® blowing agent | ||
| Side wall thickness | ||
| 2" | ||
| Front wall thickness | ||
| 4" | ||
| Crossmember floor fillers | ||
| Full length hardwood | ||
| Floor thickness | ||
| 3" | ||
| Floor underskin | ||
| .040" UCC R1 | ||
| Rear door thickness | ||
| 3" | ||
|
|
|
| Roof thickness | ||
| 3" | ||
16 Lining
|
|
|
| Front wall lining | ||
|---|---|---|
| .065" UCC R2 | ||
| Side wall lining | ||
| .065" UCC R2 | ||
| Wearband | ||
| 10" high 3⁄16" thick heavy-duty extruded aluminum non-tapered integral with floor | ||
| Rear door lining | ||
| .065" UCC R2 | ||
| Roof lining | ||
| .065" UCC R2 | ||
17 Electrical
|
|
|
| Electrical receptacle | ||
|---|---|---|
| 7-way without circuit breakers | ||
| Main harness | ||
| Utility moisture-resistant 6-wire harness with internal ground and 7-way plug | ||
| Clearance lights quantity | ||
| 0-1-2-5 D.O.T. minimum clearance light package | ||
| Rear header clearance lights | ||
| Grote® Micronova® LED grommet-mounted | ||
| Upper clearance lights | ||
| Factory choice LED with 3" mounting hole at center line | ||
| Lower clearance lights | ||
| Grote® Micronova® LED PC-rated | ||
| Side mounted directional light | ||
| Grote® Supernova® LED combo on bracket below bottom rail (each side) | ||
|
|
|
| ABS warning light | ||
| Grote® Micronova® LED PC-rated | ||
| Stop, tail, turn lights | ||
| Grote® 4" LED (10-diode) lights, 2 per side with black snap-in flange | ||
| Conspicuity tape location | ||
| On bottom rails and at rear | ||
18 Paint and Finish
|
|
|
| Front panel finish | ||
|---|---|---|
| Pre-painted white with Ultra Road Shield™ Plus (URS+) | ||
| Front corner post finish | ||
| Natural aluminum | ||
| Front subframe assembly finish | ||
| Fully immersed in black rust preventative coating (zero VOC hot dip) | ||
| Side panel finish | ||
| Pre-painted white with Ultra Road Shield™ Plus (URS+) | ||
| Rear case finish | ||
| Satin finish stainless steel | ||
| Rear subframe finish | ||
| Black scharpf | ||
| Vertical & horizontal I.C.C. bumper finish | ||
| Utility black enamel on horizontal bumper, black scharpf on vertical bumper | ||
|
|
|
| Bottom side rail finish | ||
| Natural aluminum | ||
| Top front & top side rail finish | ||
| Natural aluminum | ||
| Roof exterior finish | ||
| Natural aluminum | ||
| Support leg finish | ||
| Rust preventative coating | ||
19 Miscellaneous
|
|
|
| Mudflap type | ||
|---|---|---|
| Black plastic anti-sail with Utility logo, mounted with steel reinforcing straps | ||
| Side mounted aerodynamic air deflectors | ||
| Advanced aerodynamic side skirt USS-120A-4 | ||
20 Tires and Wheels
|
|
|
| 22.5" × 8.25" standard width wheels | ||
|---|---|---|
| Factory choice steel 10 hub piloted wheels | ||
| Tires | ||
| 295/75R 22.5” Michelin X®-Line Energy-T2 14ply Load Range 'G' | ||